All Greenville zoning districts

R-M8 zoning in Greenville County

Multifamily Residential District, Unincorporated Greenville County

R-M8 allows single-family homes by right on lots of at least 7,500 square feet, up to 8 homes per acre. Apartments are allowed by right.

Minimum lot
7,500 sf
Density limit
8 per acre
Front setback
20 ft
Height limit
45 ft

What a parcel in R-M8 holds

ParcelSingle-family lotsApartments by density
2 acres816
5 acres2140
10 acres4380
20 acres87160

A clean parcel with no flood zone or wetland, with 25% of the land kept for streets and open space. Lots are the lower of the minimum lot size count and the density limit. A real parcel loses more to its shape, hazards, and frontage. Screen a real parcel for its count.

Uses

UseStatusSource
Single-family homesBy rightTable 6.1 (row: Dwelling - single-family detached)
ApartmentsBy rightSec. 5:6Table 6.1 also shows P for Dwelling - multiple-family in R-M2 to R-M20. Apartments need a 2-acre minimum lot (Sec. 5:6.5-1).

Limits

LimitValueSource and notes
Minimum lot size7,500 sfTable 7.1Conventional single-family detached lot minimum (Table 7.1). Single-family attached lots: 1,800 sf. No minimum lot size under the Open Space option; density is capped by the district (R-M number = units per acre).
Minimum lot width30 ftSec. 7:3.9Sec. 7:3.9 sets the single-family lot width in multifamily districts (Table 7.3 points to it). Lot width is "the distance between the side lot lines at the front setback line" (Art. 3 definition, Lot, Width), i.e. at the building line.
Density limit8 per acreSec. 5:6.5-1Density equals the number in the district name (R-M8 = 8 units per acre). Sec. 5:6 sets the range from 2 (R-M2) to 20 (R-M20).
Dwellings per lotNoneThe county ordinance sets density per acre.
Front setback20 ftTable 7.3Value is for a residential service street; 30 ft on a collector and 50 ft on an arterial. Measured from the right-of-way; if unknown, measured from pavement edge and increased 10 ft (Sec. 7:3).
Side setback25 ftTable 7.3Multifamily buildings. Single-family dwellings in multifamily districts use 5 ft side and rear (Sec. 7:3.9).
Rear setback25 ftTable 7.3Multifamily buildings. Single-family dwellings use 5 ft (Sec. 7:3.9).
Front setback, single-family20 ftSec. 7:3.9Residential street; 30 ft on a collector and 50 ft on an arterial. Same as the district front setback in Table 7.3.
Side setback, single-family5 ftSec. 7:3.9Single-family dwellings only; the district side setback for other uses is 25 ft (Table 7.3).
Rear setback, single-family5 ftSec. 7:3.9Single-family dwellings only; the district rear setback for other uses is 25 ft (Table 7.3).
Height limit45 ftTable 7.3Sec. 7:3.7 lets buildings exceed the district height if side and rear yards increase 1 foot for each 3 feet of extra height.
Story limitNoneThe County Zoning Ordinance regulates height in feet only; no story limit found in Table 7.3/7.4.
Lot coverage limitNoneNo maximum lot coverage standard for this district found in Articles 5 and 7 of the County Zoning Ordinance; site yield is set by setbacks, parking, buffers and stormwater.
Floor area ratio limitNoneThe County Zoning Ordinance has no floor area ratio standard (searched the full text).
Parking per apartment1.5 spacesTable 12.1, item 4Bedroom-based: 1 space per 1-BR or efficiency, 1.5 per 2-BR, 2 per 3+ BR, plus visitor parking equal to 10% of required spaces. 1.5 is the 2-BR ratio; compute from the unit mix. Structures of four units or fewer: 1.5 per unit.

Screen a parcel zoned R-M8

Search an address or parcel number. The screen loads the parcel, finds its district, removes setbacks, flood zones, and wetlands, and counts lots and apartments with these limits.

Screen a parcel Listing sheets for agents

Other Greenville County districts

  • R-M5 Multifamily Residential District
  • R-M6 Multifamily Residential District
  • R-M7 Multifamily Residential District
  • R-M10 Multifamily Residential District
  • R-M12 Multifamily Residential District
  • R-M14 Multifamily Residential District

Limits from the Greenville County Zoning Ordinance, read November 20, 2026. Source document. Ordinances change and overlays can add limits. Confirm the district and its limits with Greenville County Zoning Administration before you rely on them.